How a Vehicle's Structure Handles a Crash
V
Crash energy has to go somewhere, and today's structures are built to manage it. Sections called crush zones are designed to fold and absorb that energy, and I-CAR says the growing use of high-strength steel has changed the load path, sending collision forces farther into the vehicle.
The unibody, as Kelley Blue Book describes it, is a frame and body skeleton built as one piece, so frame damage on one can involve the pillars and strut towers. Body-on-frame layouts, which keep a separate ladder frame, are now confined to pickups and a small number of big SUVs and vans.
- Crush zones: sections built to fold and absorb energy
- I-CAR: more high-strength steel, new crash load paths
- KBB: pillars and strut towers can be unibody frame damage
- KBB: pickups still use body-on-frame, as do a few big SUVs
- I-CAR: the stronger the steel, the less repairable
Collision Services
Symptoms of Frame or Unibody Damage
V
Uneven seams around the hood, trunk and doors, along with doors that suddenly stick, are possible frame damage signs, according to Kelley Blue Book. There is a structural reason doors matter: hinges on newer vehicles are often non-adjustable, I-CAR notes, so they may not fit properly unless the structure matches the automaker's measurements.
On the road, KBB adds steering that keeps pulling after an alignment and tires wearing unevenly. Michelin notes a pull can also come from uneven tire pressure or a caliper that sticks, so read each sign as a reason to have the structure measured. The shop's Request an Estimate page covers scheduling and questions.
- Hood, trunk or door seams that no longer look even
- A door that suddenly sticks
- Steering that pulls even after an alignment
- Tires wearing in strange or uneven patterns
- I-CAR: a straight-looking car can still measure out of spec
Request an Estimate
Frame Straightening Machines and Measurement
V
Frame straightening machines are part of the equipment Jenkins Collision Center of Leesburg has invested in, and its team handles frame alignment and structural repairs. Frame alignment means straightening the structure back to the dimensions it was built to, a separate job from aligning the wheels.
The yardstick is the automaker. I-CAR says vehicle makers often supply specific dimensions to hit rather than a tolerance band, and it advises checking measuring points often during the repair, along with test fitting of panels. On GM vehicles, the part-specific repair procedures call for measuring with three-dimensional equipment.
- Frame straightening machines among the shop's equipment
- Facilities equipped for all makes and models
- Frame alignment: the structure, not the wheels
- I-CAR: tolerances on newer cars run tighter than before
- I-CAR: test fit panels and recheck measuring points
Why Choose Us
When Structural Parts Get Replaced
V
Who decides: straighten or replace? I-CAR sends repairers to the body repair manual and the automaker's position statements first, with its best practices last. By its definition, a part is kinked if straightening leaves a permanent deformation that will not return to shape without excessive heat, and a kinked part has to be replaced.
Sectioning splices in a piece cut from a new service part, away from a factory seam, and I-CAR says not to section without the automaker's published procedure. On Toyota and Lexus full-frame vehicles, frame sectioning is not an approved Toyota repair. Today's energy-managing structures mean plenty of bent parts get replaced too, I-CAR adds.
- I-CAR: body repair manual first, its best practices last
- I-CAR: replace a bent part if the automaker says to
- I-CAR: bumper reinforcements are off-limits for straightening
- Hyundai (2025): replace damaged ultra-high-strength steel at factory seams
- I-CAR: section only with a published automaker procedure
Certified Repairs
Wheel Alignment After Structural Work
V
Frame alignment comes first. I-CAR says a wheel alignment can be done properly only once the structure is correct in all three dimensions; a car with leftover damage may seem to align, then wear its tires abnormally over time. Collision energy can also damage suspension parts outside the impact zone, I-CAR adds.
I-CAR's guidance is to check the alignment once repairs are completed, typically when steering parts or a tie rod were replaced. The Leesburg shop lists wheel alignment and suspension services, and its certifications page credits the I-CAR Gold Class Certified Team. On top of that, the shop extends a lifetime warranty on all repairs performed at Jenkins Collision Centers.
- I-CAR: side collisions can change a wheel's position
- I-CAR: a 4-wheel alignment when a check finds misalignment
- Honda's ProFirst Collision Repair Facility recognition
- Recognized Collision Repair Center status from Hyundai and Kia
- Credentials include Certified Assured Performance and Nissan Collision Repair Network membership
Meet Our Staff